-
product
Setup Integrity Checker For B2980 Series, Fixed Perpetual License
N1420A
The N1420A is optional software to compare, evaluate and record noise from test setup. It is helpful when you isolate the cause of noise related to setup elements such as cables, connectors, shields, chambers, etc.
-
product
Keysight 32-Channel FormC/Form A General Purpose Switch for 34980A
34937A
The Keysight 34937A is a general-purpose switch module for the 34980A Multifunction Switch/Measure Unit. It has 28 independent single-pole, double-throw (SPDT) 1A relays and 4 single-pole, single-throw (Form A) 5A relays. This module is used to cycle power to products under test, control indicator and status lights, and to actuate external power relays and solenoids. The Form C channels are 300V, 1A contacts and can handle up to 60W, and the Form A channels are 30VDC/250VAC, 5A contacts and can handle up to 150W. Standard 50-pin Dsub connectors allow for use with standard cables, terminal blocks, or mass interconnect solutions.
-
product
Cable/Harness Test System with Rack-Mounted Switching
CKT1175-20
The CKT1175-20 is a high-voltage wiring analysis system that features rack-mounted switching matrices. This system is expandable in 100 test point increments to 96,000 test points, and available with a wide variety of adapter cable interface connectors, with the standard interface being the CKT MAC interface system.
-
product
Mini Array+
DORC's ZX-1
Direct Optical Research Company
Used primarily to measure multi fiber (MT/MPO and MT-RJ) connectors, DORC's fourth generation "ZX-1 mini Array+" is the result of 18 years of hardware and software product development. Although optimized for mutifiber connectors, the ZX-1 mini Array plus also does an excellent job of measuring single fiber PC and APC connectors. DORC's patented design is based on a variant of the Michelson configuration, and provides BOTH 2D and 3D high resolution images of the sample under test in approximately 45 seconds for multi fiber connectors and just 3-4 seconds for single fiber connectors - from the time the connector is inserted.
-
product
96 Channel DPST Relay And Control PXI Carrier Card
GX6196
The GX6196 is a 6U PXI switch and control board that can be used to create custom switching, signal conditioning, or specific UUT control interfaces. The board provides 96, 2 pole, form A relays, 8 digital I/O lines, and a serial digital interface. All of these resources are available via (5) inter-board connectors which interface to the user defined daughter / mezzanine board. The mezzanine board provides all connections to the unit under test (UUT) via two 78 pin D-sub connectors. The GX6196 is supplied with a front panel which accepts (2) 78 pin D-sub connectors.
-
product
Microohmmeter
AD-7100
4 Connectors measurement method, Max measurement time 10 sec Indicator of right connect test cables, Lock of test current connectors, Graphical backlight LCD display (240 x 128), True test current indicator, Temperature control of test current stability system,
-
product
Cable Tester
CableJoG 128
The CableJoG 128 can test up to 128 individual connections of all manufacturers of connectors. This simple test instrument stores up to 55 separate connection configurations. Each cable that is tested is compared with the configuration stored in its memory to produce a pass/fail indication of each pin connection.
-
-
product
15 Pin Breakout Interface
VSI-Breakout-15
The VSI-Breakout-15 is a very useful tool in debugging signals or software in a system. It allows unlimited access to signals within the cabling that might otherwise be difficult to access. The board gives test points at each side of the connector and jumper with a easy to use tabbed shunt to allow for easy disconnection of any particular signal between the connectors. The jumpers also give an opportunity to inject a signal regardless of what signal was originally being driven.
-
product
Validation System
FLEX BMS
The FLEX BMS™ Validation System is a quick-connecting, highly flexible test system for rapid evaluation of centralized, single-board and distributed battery management systems. Utilizing Bloomy’s industry-leading battery cell simulators, COTS instrumentation, industry-standard connectors, and models that run in real-time, the FLEX BMS™ Validation System can easily be reconfigured to test a wide variety of BMSs. The FLEX BMS™ Validation System is used by national and regional safety and standards labs for certifying the BMS for a wide array of e-mobility products and applications.
-
product
Insulation Tester
AD-2050
Measuring voltage control during measurement, Insulation measurement up to 400 G W. Elimination of trough resistance insulation. 3 connectors measurement method, Autoranging, Auto-Discharge facility safely discharges the connected circuit after a test, 5 minutes, 1 minute at will shorter measurement,
-
product
64-Channel Boundary-Scan Digital I/O Scan Module
JT 2111/MPV DIOS IDC
The JT 2111/MPV is a 64 channel boundary-scan digital I/O scan module enclosed in an impact resistant housing. The module is designed to test and control edge connectors, on-board connectors and logic clusters in boundary-scan applications. Multiple modules can be connected serially to increase the number of I/Os. Available with 96-pin DIN 41612 connectors and 20-pin 0.1″ pitch IDC connectors.
-
product
9 Pin Breakout Interface
VSI-Breakout-9
The VSI-Breakout-9 is a very useful tool in debugging signals or software in a system. It allows unlimited access to signals within the cabling that might otherwise be difficult to access. The board gives test points at each side of the connector and jumper with a easy to use tabbed shunt to allow for easy disconnection of any particular signal between the connectors. The jumpers also give an opportunity to inject a signal regardless of what signal was originally being driven.
-
product
67 GHz Test Port Extension Cables
Spanawave's test port extension cables are the perfect alternative to over-priced models from other manufacturers. These test cables provide the utmost precision in vector measurements in the lab and during calibrations. Besides the electrical performance, these VNA cables are rugged and feature a lightweight armor to insure consistent performance over time. A wide variety of connectors are available including the precision "NMD" or "port ruggedized" connectors, which mate directly to the VNA port. Custom lengths and configurations are available. Please contact us for application help and pricing.
-
product
Low PIM Coaxial Cable Assemblies
For applications that demand low VSWR, low insertion and low PIM cable assemblies; RFI now offers semi-rigid and corrugated cable assemblies with factory soldered N and DIN connectors. Assembled using the latest soldering equipment for years of performance reliability. Each assembly is tested for insertion loss, VSWR and PIM rating and is shipped with individual test data. Available using flexible or super flexible corrugated cables with a standard or fire retardant jacket.
-
product
50 GHz Test Port Extension Cables
Spanawave's test port extension cables are the perfect alternative to over-priced models from other manufacturers. These test cables provide the utmost precision in vector measurements in the lab and during calibrations. Besides the electrical performance, these VNA cables are rugged and feature a lightweight armor to insure consistent performance over time. A wide variety of connectors are available including the precision "NMD" or "port ruggedized" connectors, which mate directly to the VNA port. Custom lengths and configurations are available. Please contact us for application help and pricing.
-
product
PXI Expandable 16x16 RF Matrix 50Ohm Lemo 00
45-720A-541
The 45-720A module is a 6U 16x16 RF Matrix suitable for switching frequencies to beyond 250MHz. The 45- 720A module is available in 50 and 75 Ohm versions with a choice of coaxial connectors. It is intended for the easy construction of high performance bidirectional matrix switching systems. Automatic Isolation Switches are located on all coaxial connectors, these disconnect the matrix from the external test fixture. This maximises isolation and RF performance.
-
product
Test Cables
Test cables for tone generators, butt sets, oscilloscopes, digital multi-meters (DMM), and other test equipment that uses specialized connectors like Bed of Nails alligator clips, RJ11, sheathed banana plugs, etc. Our cables are similar and replaces genuine manufacturer cables from Fluke, Harris, Tektronix, HP, JDSU etc.
-
product
PXI Voltage Amplifier 10K Ohm, SMB
41-650-012
The 41-650 is a 5 channel voltage amplifier ideal for increasing the output voltage from other PXI modules, enabling users to easily generate the signal voltages commonly required in applications such as automotive test. Each amplifier can be independently programmed to a gain of 1, 2, 5, 10 or 20, enabling it to be used with modules with low output voltage capability. Inputs and outputs can be provided either on SMB connectors or on a D Type connector to suite the user’s wiring system.
-
product
R.F. Coupler and high Pass Filter
7415-3
There are those who disagree with the r.f. conducted susceptibility test setup of Method CS02 of MIL-STD-462. Homemade rigs have sprouted to comply with the coupling capacitor requirement, each with it own disadvantage. Our little Type 7415-3 R.F. Coupler is the answer. A neat little box with BNC connectors and a pair of binding posts, it is rated at 270 V.A.C. at the LINE terminals and 20 volts PMS into the GEN port. Looks good and does a fine job.
-
product
PCB Test Connectors
Tag-Connect
Tag-Connect is a simple and secure way of connecting debuggers, programmers and test equipment to your PCBs. Tag-Connect uses a specially designed and patented connector for making the connection to your PCB (Patent Pending for the -NL versions). Tag-Connect eliminates the need for a programming or JTAG connector on your PCB.
-
product
PXI Expandable 16x16 RF Matrix 75Ohm Type 43
45-720A-711
The 45-720A module is a 6U 16x16 RF Matrix suitable for switching frequencies to beyond 250MHz. The 45- 720A module is available in 50 and 75 Ohm versions with a choice of coaxial connectors. It is intended for the easy construction of high performance bidirectional matrix switching systems. Automatic Isolation Switches are located on all coaxial connectors, these disconnect the matrix from the external test fixture. This maximises isolation and RF performance.
-
product
RF Components
Our Components product line consists of standard RF components and unique designs for custom microwave applications. We provide rugged, reliable and quality solutions for low and high power attenuation, termination, coupler, and power-divider applications. In addition to our extensive line of standard products, Bird has a reputation for designing custom solutions for custom applications. Bird has done hundreds of special versions of RF components to meet the unique needs of our customers. Common...show more -
product
Digital Micro OHM Meter
NMC's Digital Micro Ohm Meters are low cost, compact, light weight, 3½ digit resistance meter suitable for measurements of resistances of cables, wires, transformers, motor windings, coils and contact resistance of switches, connectors, relays and track resistance of PCB's etc. The value of resistance is displayed on 7 segment LED display. Four terminal measurement systems provide measurements free from errors due to contact resistance and test lead resistance.
-
product
Retractable Cable
3700
Peaceful Thriving Enterprise Co Ltd
*2 x 6m retractable test leads.*Used as an extension cord for cars, trailers, boats and more.*Optional accessory included alligator clips, test probes and banana plugs.*The tester can be used with any multi meter or device equipped with banana jack connectors.
-
product
PXI 12x8 RF Matrix 300MHz 50 SMB - With Loop-Thru
40-726A-511-L
The 40-726A is a 12x8 RF Matrix Module suitable for switching frequencies up to 300MHz (50Ω version). The 40-726A is available in either 50Ω or 75Ω versions with a choice of coaxial connectors. The module is designed to provide a simple and scalable bidirectional matrix for RF frequencies. Isolation Switches are located on all coaxial connectors, these disconnect the matrix from the external test fixture. This maximizes isolation and RF performance.
-
product
High Density Switches
Marvin Test Solutions’ switch card portfolio includes matrix, multiplexer, and RF multiplexer configurations. 3U and 6U PXI switch cards feature easy to use, reliable, and integration-friendly D-sub style interface connectors – a feature unique to Marvin Test Solutions PXI switch cards. GENASYS switch cards are compatible with MTS’s family of GENASYS Switching and Switching/Digital Subsystems, featuring integrated MAC Panel SCOUT receivers.
-
product
2-in-1 High-Voltage Test Hood
LX-HVE900EC
The test cells are made of stable, highly insulating plastic and are closed by a swiveling, transparent cover. The built-in safety switch is used to lock the hood and release the high-voltage sources. This ensures that no high voltage is active when the door is open. There is a generously dimensioned wiring space in the floor of the test cage. An interchangeable adapter plate in the test cell - optionally with an interchangeable interface or an interchangeable adapter cassette - allows quick ada...show more -
product
UNI-T Series
Weshine Electric Manufacturing Co., Ltd
mainly used to measure the wire resistance of cables, the contact resistance ofswitches, connectors, relays, the resistance of coils, motors, transformer windings, and equipment enclosures, lightning protection belts, ground beams, structures, cabinets, steel bars, Test the connection resistance between metal components of water pipes, windows, guardrails, radiators, assembly lines, etc. It is widely used in telecommunications, electric power, meteorology, computer rooms, oil fields, power distribution lines, tower transmission lines, gas stations, factory grounding grids, lightning rods, etc.
-
product
Weld Testers
The Weld Tester is our most versatile electrochemical monitoring instrument. Housed in a substantial metal case with brushed anodised aluminium front panel and green military specification connectors this equipment looks functional and professional. The top row of connectors are exactly the same as provided on a Gill 12 whilst the bottom row are for the additional weld segments. Using the same Potentiostat, Galvanostat, Zero Resistance Ammeter with integrated Frequency Response Analyser and Sweep Generator as a Gill 12 allows all the tests supplied with the Gill 12 to be supplied with the Weld Tester.
